The question of how, among a huge number of different components, choose a truly high-quality drill for a punch is relevant for each owner of this tool. In addition, difficulties may arise and, for example, when choosing a peak or shoulder blades for it. In a word, knowledge about which equipment should be used in one case or another will definitely not be superfluous.
How to choose a fusion on a punch?
Video — what is a punch and how to use it
First of all, when buying drills and any other equipment, you should pay attention to their tail. To date, two types are common:
SDS-MAX;
SDS+.
The first of them are used in light and medium instruments, the mass of which does not exceed five kilograms, and the latter in heavy. Despite the fact that now, in principle, you can buy any adapter that allows you to insert, for example, the SDS+ drill into the SDS-MAX cartridge, experienced craftsmen do not recommend doing this.
The use of unsuitable equipment can lead to a breakdown of the tool and the need to purchase new parts, for example, an anchor for a perforator will certainly come to change.
Another important point when choosing a spell is the intensity of the slope of the sludge. In order to drill a deep hole, you need to choose a screw boura. A small angle of inclination of the grooves on the storm will tell that such equipment is designed for prolonged operation, provided that a low load on the tool. If the angle of inclination is large, then the drill is intended for short -term work with a large load. The diameter of the drill should be exactly the same as the diameter of that screw or dowel that will be inserted into the prepared hole.
Tape for the perforator and similar equipment with it
How to extend the life of a punch — video
In addition to drilling holes, the punch is able to perform other work with brick, concrete or stone. The chisel is necessary if it is planned to dismantle the tile or, for example, it is required to repel an extra piece of plaster on the wall or “influx” of concrete on the floor. Most often, for such work, shoulder blades from two and a half to six centimeters are used. Peak for a perforator is used in cases where it is required to break through the hole in the wall or make a stroke for electrical wiring. It is well suited for making holes in reinforced concrete, as it is able to break through metal reinforcement. A drip for a perforator with a wide tip can turn a powerful tool into a real jack hammer that can remove layers of asphalt.
There is also another type of chisel — a strobber for a perforator, or as it is sometimes called, channel chisel. Its tip is a U-shaped blade, with which a stroke is made in a concrete wall. However, unlike the one that remains after the stroke of the peak, the edges of it are even. The diameter of the «spoon» in such a device can be both large and small. Depending on this, it can be intended for strokes for wiring or laying of water pipes during the repair of bathrooms and kitchens. A bit for a perforator may have other forms. For example, in the form of a flat shoulder blade bent upward. Such a device is used to remove old seams in brickwork.
Today on sale you can find sets in which there are all types of perforator chisels. However, a good set is very expensive, and you can purchase cheap only if the tool is used for rare and short work. Otherwise, it is better to buy all components separately as necessary.
Mixer for a perforator and other devices
The tool can also be used as a mixer to knead dry plasters and tile adhesives. To do this, you need to purchase a special mixer nozzle — exactly the same as it is used when working with a drill (of course, with a suitable shank). It is worth remembering that when kneading, the punch should be put in the mode of unstressed drilling. If the tool is not provided for such an opportunity, it is better not to take risks and stir the composition manually.
For drilling holes for sockets and switches, special nozzles are used with special spraying along the cutting edge. When working with such equipment, you also need to turn off the impact mode, otherwise it will almost instantly become unusable. The cost of crowns is quite high — high -quality components can cost several thousand rubles.
And at the end of the article, several tips on working with a perforator. If you need to drill concrete to a great depth, you need to start work with a short drill. It should be the same diameter as the required hole; You need to move to work with a long drill only when the short is not enough. During operation, you do not need to press hard on the tool — this can lead it to a breakdown. In addition, during long work by a drill or chisel, their shank must be periodically treated with a special lubricant.
Do not forget about your own safety. To protect your eyes and respiratory tract from dust and pieces of concrete, you need to wear special glasses and respirator.